In precision sensor signal conditioning, medical instruments, and automotive sensor systems, sources of error often stem not from the ADC’s resolution, but from the offset voltage and temperature drift of the front-end amplifier. When the sensor output is only a few tens of microvolts and the system must remain stable over a temperature range of −40°C to +125°C, the offset drift of a typical precision op-amp can quickly erode the effective dynamic range. ADI’s AD8628 is a zero-drift, single-supply rail-to-rail input/output (RRIO) operational amplifier specifically designed to address this challenge. With 1 μV-level offset and near-zero temperature drift, it is the preferred choice for high-precision signal chains where “zero error sources” are essential. Mingjiada Electronics now offers a full range of AD8628 package types in brand-new, genuine, and in-stock quantities. This article covers technical specifications, application scenarios, and procurement guidelines.
Why Precision Signal Chains Require “Zero-Drift” Op-Amps
The offset voltage of traditional precision op-amps typically ranges from tens to hundreds of microvolts, with temperature drift in the range of 0.5 to 2 μV/°C. After calibration at room temperature, a change in ambient temperature of just tens of degrees Celsius can cause the offset drift alone to exceed the full-scale output of the sensor. Take thermocouples or strain gauge bridges as examples: their output signals are typically in the range of hundreds of microvolts to millivolts. If the drift of the front-end amplifier reaches microvolts per degree Celsius, the DC error will directly overwhelm the actual signal.
Zero-drift amplifiers continuously correct offset through internal auto-zero or chopping mechanisms, thereby eliminating low-frequency 1/f noise and temperature drift in principle. The AD8628 employs ADI’s proprietary combined auto-zero and chopping topology, which significantly reduces the digital switching noise commonly found in traditional chopping amplifiers while maintaining zero-drift characteristics, and enables stable operation without the need for external capacitors. This architectural choice achieves a practical balance among “low offset,” “low noise,” and “small size,” rather than sacrificing noise performance to achieve zero drift.
AD8628 Core Features: Precision Specifications Anchored at 1 μV Offset
The key parameters of the AD8628 focus on “eliminating DC errors,” with the primary specifications as follows:
Input offset voltage (Vos): 1 μV (typical)
Input offset drift: 0.002 μV/°C (typical), <0.005 μV/°C
Low-frequency noise (0.1–10 Hz): 0.5 μV p-p
Input bias current: 30 pA (typical), 100 pA (maximum)
Gain-bandwidth product (GBW): 2.5 MHz
Common-mode rejection ratio / Power-supply rejection ratio: 130 dB / 130 dB
Supply current: 1.0 mA (typical)
Supply voltage range: 2.7 V to 5 V (single supply); ±1.35 V to ±2.5 V (dual supply)
Input/output swing: Rail-to-rail (RRIO)
Overload recovery time: 50 μs
Operating Temperature Range: −40°C to +125°C
External Capacitance: No external capacitance required
Notably, the 130 dB CMRR and PSRR are among the highest levels found in single-supply, low-voltage operational amplifiers. This means that in embedded environments where power supply noise and common-mode interference coexist, the device itself offers strong interference suppression capabilities, thereby reducing the design burden associated with downstream filtering and shielding. The maximum input bias current of 100 pA directly benefits high-impedance sensor interfaces—signal sources such as photodiodes and pH electrodes can have source impedances ranging from megaohms to gigaohms. For every 1 nA increase in bias current, an additional 1 mV of error is introduced across a 1 MΩ source impedance; the 100 pA level keeps this error below 100 microvolts.
In terms of packaging, the AD8628 is available in three options: a 5-pin TSOT, a 5-pin SOT-23, and an 8-pin narrow-body SOIC. Models with the “W” prefix are certified for automotive applications and are suitable for space-constrained automotive sensor modules and portable medical devices.
Typical Applications for the AD8628
The AD8628’s combination of specifications makes it ideally suited for scenarios characterized by “low signal amplitude, high source impedance, wide temperature ranges, and tight error budgets.” The following application areas directly correspond to its characteristics:
Signal conditioning for pressure and position sensors. The bridge outputs of piezoresistive or capacitive sensors are typically in the millivolt range; the zero-drift characteristic ensures that bridge offset does not drift with temperature over a wide temperature range, eliminating the need for frequent system-level calibration.
Precision current sensing (high-side sensing). The AD8628 can serve as the core amplifier in a discrete high-side current sensing solution. Its 130 dB CMRR enables it to extract minute shunt voltages even when the common-mode voltage is close to the supply rail, making it suitable for battery management, motor drives, and power supply monitoring.
Thermocouple and Thermopile Amplifiers. Thermocouple outputs are in the microvolt-per-degree Celsius range; the AD8628’s 0.5 μV p-p low-frequency noise and 1 μV offset allow for reliable amplification without the need for significant signal filtering, making it suitable for temperature measurement and infrared thermopile sensing.
Photodiode amplifiers. A maximum bias current of 100 pA keeps dark current errors low in photocurrent measurements, while the zero-drift characteristic prevents the baseline from slowly shifting with temperature during long-term measurements.
Strain Gauge Amplifiers and Medical Instruments. Offset drift in a strain gauge bridge directly manifests as zero-point drift in weight or force measurements; the AD8628’s drift of 0.002 μV/°C reduces this error to a nearly negligible level, making it equally suitable for low-speed, high-precision medical signal chains such as electrocardiograms and blood pressure monitoring.
Reference Buffers and ADC Input Drivers. In high-resolution systems with 16 bits or higher, the AD8628 can serve as a reference voltage buffer or an ADC input driver; its low offset and rail-to-rail output swing help fully utilize the ADC’s full-scale range and reduce gain error.
Mingjiada Electronics: Full AD8628 Series in Stock
Shenzhen Mingjiada Electronics Co., Ltd. has long specialized in the supply and inventory management of electronic components, maintaining a stable product line and deep inventory in the field of precision operational amplifiers. As one of Mingjiada’s key zero-drift/low-offset op-amp models, the AD8628 meets procurement needs ranging from R&D prototyping to mass production.
Supply options include:
AD8628 Single-Channel Full Package Lineup: 5-pin TSOT (AUJZ series), 5-pin SOT-23 (ARTZ series), 8-pin narrow-body SOIC (ARZ series), including standard versions and automotive-certified versions with the “W” prefix;
Complementary Models in the Same Series: AD8629 (dual-channel) and AD8630 (quad-channel), facilitating unified selection within the same signal chain;
Packaging Options: Available in reel and tube formats, compatible with SMT production lines and manual assembly scenarios;
Service Model: Brand-new, genuine, in-stock products; supports small-batch sample purchases and rapid delivery for large-volume orders.
To obtain the latest quote or confirm inventory for the AD8628, please contact Mingjiada Electronics:
Phone/Mobile: +86 13410018555
Email: sales@hkmjd.com
Website: www.integrated-ic.com
Address: 1239-1241, New Asia Guoli Building, Zhenzhong Road, Futian District, Shenzhen
담당자: Mr. Sales Manager
전화 번호: 86-13410018555
팩스: 86-0755-83957753
Korean
