회사 블로그 Mingjiada Supply And Recycle ADI ADXL318-1WBCCZ Low Noise Low Power 3-Axis MEMS Accelerometer

Mingjiada Supply And Recycle ADI ADXL318-1WBCCZ Low Noise Low Power 3-Axis MEMS Accelerometer

ADXL318-1WBCCZ is a low-noise-density, low-power, wide-bandwidth triaxial MEMS accelerometer launched by ADI, housed in a 14-pin LGA package (measuring just 2.9 mm × 2.8 mm × 0.87 mm). The ADXL318-1WBCCZ supports selectable measurement ranges of ±4g, ±8g and ±16g, and offers industry-leading noise performance, enabling precision applications with minimal calibration. Its low-noise and low-power characteristics allow it to accurately measure audio signals even in high-vibration environments.

Shenzhen Mingjiada Electronics Co., Ltd. – Long-term stock availability of the ADXL318-1WBCCZ ADI three-axis MEMS accelerometer; genuine original products; supporting small-batch samples and long-term project orders; we also specialise in the buy-back of various electronic components, including ADI sensors, MCUs, power management ICs, memory, FPGAs and image sensors.

ADXL318-1WBCCZ Key Specifications:
Measurement axes: X / Y / Z (three axes)
Selectable ranges: ±4 g, ±8 g, ±16 g
Noise density: 20 μg/√Hz (XY), 27 μg/√Hz (Z)
Bandwidth: 4 kHz (with digital correction, relative flatness <0.5 dB@3.8 kHz)
Power consumption: typically 340 μA (VS = 2.25–3.6 V or 1.8 V V1P8); VDDIO: 1.14–3.6 V (1.62–3.6 V over the full temperature range)
ADC resolution: 16-bit
Digital interfaces: SPI / I²C (control) + I²S / TDM / PDM (audio data output)
On-chip resources: 320-word FIFO, programmable LPF/HPF, on-chip temperature sensor, configurable interrupts, electromechanical self-test (10,000 g mechanical shock tolerance)
Group delay: PDM < 50 μs, I²S/TDM < 110 μs

ADXL318-1WBCCZ Key Features:
Ultra-low noise density: 20 μg/√Hz (X/Y axes), 27 μg/√Hz (Z axis)
Typical power consumption 340 μA, low-power continuous sampling
4 kHz high-frequency bandwidth; 0.5 dB in-band frequency flatness at 3.8 kHz with digital correction
Extremely low transmission delay: I²S/TDM < 110 μs; PDM < 50 μs
Three-axis acceleration sensing, with software-selectable ranges: ±4 g, ±8 g, ±16 g
16-bit analogue-to-digital converter, with selectable synchronous/asynchronous sampling modes
Multi-protocol interfaces: SPI, I²C, I²S, TDM, PDM
320-level output FIFO to reduce read load on the host controller
Integrated on-chip temperature sensor and programmable interrupt generator
Built-in electromechanical self-test and programmable high-pass and low-pass filters

Typical applications for the ADXL318-1WBCCZ:
Automotive road noise cancellation (RNC)
Condition-based monitoring
Robotics

Shenzhen Mingjiada Electronics Co., Ltd. – ADXL318-1WBCCZ One-Stop Supply + Recycling
Mingjiada Electronics consistently supplies brand-new, genuine ADXL318-1WBCCZ (and related models such as the ADXL318-2WBCCZ), whilst offering high-value recycling services for the full range of ADI MEMS sensors, accelerometers, IMUs, gyroscopes and automotive-grade surplus stock.
Supply Services: We provide genuine, factory-sealed products in stock, supporting both sample purchases and bulk orders, with rapid delivery backed by efficient logistics.
Buyback Service: Covers ADI inertial devices such as the ADXL318, ADXL345, ADXL356, ADXL362 and ADIS164xx series, as well as comparable MEMS products from ST, Bosch, TDK InvenSense and Murata; we only accept goods sourced through official channels (such as distributors, traders and end-user factories) and do not accept goods from unofficial sources.

For further information regarding the [ADI] ADXL318-1WBCCZ – a low-noise, low-power, wide-bandwidth, 3-axis MEMS accelerometer – or to purchase samples or enquire about buy-back prices, please visit the Mingjiada Electronics website (https://www.integrated-ic.com/) for further details on supply and demand.